04-27-2023, 12:54 PM
UPDATE
![[Image: P4260041.jpg]](https://i.postimg.cc/D8DmXy5J/P4260041.jpg)
Finally got a good day, so I took
the plunge removing fuel tank
![[Image: P4260042.jpg]](https://i.postimg.cc/njHLJsV5/P4260042.jpg)
Removal of sending unit
![[Image: P4260043.jpg]](https://i.postimg.cc/XZ6JsHRn/P4260043.jpg)
Upon removal found intake screen
broken away but was held in place with
sender holding against tank bottom
![[Image: P4260044.jpg]](https://i.postimg.cc/5QyNXZCS/P4260044.jpg)
![[Image: P4260045.jpg]](https://i.postimg.cc/MvXvHj0J/P4260045.jpg)
Remove housing cover for inline
screens. Right side completely clogged,
left was about 80%+ clogged
![[Image: P4260046.jpg]](https://i.postimg.cc/sGgqszhs/P4260046.jpg)
![[Image: P4260047.jpg]](https://i.postimg.cc/G8r6gG3B/P4260047.jpg)
![[Image: P4260048.jpg]](https://i.postimg.cc/tZ5wKJ7B/P4260048.jpg)
This is what they should look like
after cleaning
![[Image: P4260049.jpg]](https://i.postimg.cc/2qnPx2YR/P4260049.jpg)
Then I started on the modification
![[Image: P4260050.jpg]](https://i.postimg.cc/5XQcXfkt/P4260050.jpg)
The intake pipe added is 4" with new
intake screen at the bottom. The "Z"
pipe is added to extend beyond
float, this is fuel return from engine
after heated
![[Image: P4260041.jpg]](https://i.postimg.cc/D8DmXy5J/P4260041.jpg)
Finally got a good day, so I took
the plunge removing fuel tank
![[Image: P4260042.jpg]](https://i.postimg.cc/njHLJsV5/P4260042.jpg)
Removal of sending unit
![[Image: P4260043.jpg]](https://i.postimg.cc/XZ6JsHRn/P4260043.jpg)
Upon removal found intake screen
broken away but was held in place with
sender holding against tank bottom
![[Image: P4260044.jpg]](https://i.postimg.cc/5QyNXZCS/P4260044.jpg)
![[Image: P4260045.jpg]](https://i.postimg.cc/MvXvHj0J/P4260045.jpg)
Remove housing cover for inline
screens. Right side completely clogged,
left was about 80%+ clogged
![[Image: P4260046.jpg]](https://i.postimg.cc/sGgqszhs/P4260046.jpg)
![[Image: P4260047.jpg]](https://i.postimg.cc/G8r6gG3B/P4260047.jpg)
![[Image: P4260048.jpg]](https://i.postimg.cc/tZ5wKJ7B/P4260048.jpg)
This is what they should look like
after cleaning
![[Image: P4260049.jpg]](https://i.postimg.cc/2qnPx2YR/P4260049.jpg)
Then I started on the modification
![[Image: P4260050.jpg]](https://i.postimg.cc/5XQcXfkt/P4260050.jpg)
The intake pipe added is 4" with new
intake screen at the bottom. The "Z"
pipe is added to extend beyond
float, this is fuel return from engine
after heated