01-13-2007, 03:01 AM
[black][size 3]Here are some photos of the actual device as I used it.[/size][/black]
[black][size 3][/size][/black]
[black][size 3][/size][/black]
[black][size 3]With conventional, level wind, and baitcaster reels, the set up looks like this.[/size][/black]
[black][size 3][inline 2007_0112Image0008r.JPG][/size][/black]
[black][size 3][/size][/black]
[black][size 3][/size][/black]
[black][size 3]With spinning reels, it looks like this. [/size][/black]
[black][size 3][inline 2007_0112Image0006r.JPG][/size][/black]
[black][size 3][/size][/black]
[black][size 3][/size][/black]
[black][size 3][/size][/black]
[size 3][black]Below are some of the included small parts:
[/black]1. In the middle of the photo, there is a single small screw - that along with the piece of plastic that looks kind of like a "Z" holds the line stripper, it is interchangable with the screws that hold in the corkscrew looking spool holding devices. [/size]
[size 3]2. The cork screw looking things(spool tensioners) on the left are the parts that hold the filler spool on the chromed spool holding arm bracket that is on the right of every thing else[/size][size 3].[/size][size 1]
[/size][black][size 3]3. The two grommets under the angled piece that holds the line stripper are the ones in the documet that are supposed to be used for holding the spool while doing spinning reels. [/size][/black]
[black][size 3]4. The two reddish round parts in the center of the photo, are parts that I do not know what they do, and they are not mentioned anywhere in the directions or the supplimentary supplied trouble shooting information. [/size][/black]
[black][size 3]5. The black odd shaped rubber piece towards the bottom(not included) is one I fashioned to hold the spool bracket steady while spooling.[/size][/black]
[black][size 3][inline 2007_0112Image0012r.JPG][/size][/black]
[signature]
[black][size 3][/size][/black]
[black][size 3][/size][/black]
[black][size 3]With conventional, level wind, and baitcaster reels, the set up looks like this.[/size][/black]
[black][size 3][inline 2007_0112Image0008r.JPG][/size][/black]
[black][size 3][/size][/black]
[black][size 3][/size][/black]
[black][size 3]With spinning reels, it looks like this. [/size][/black]
[black][size 3][inline 2007_0112Image0006r.JPG][/size][/black]
[black][size 3][/size][/black]
[black][size 3][/size][/black]
[black][size 3][/size][/black]
[size 3][black]Below are some of the included small parts:
[/black]1. In the middle of the photo, there is a single small screw - that along with the piece of plastic that looks kind of like a "Z" holds the line stripper, it is interchangable with the screws that hold in the corkscrew looking spool holding devices. [/size]
[size 3]2. The cork screw looking things(spool tensioners) on the left are the parts that hold the filler spool on the chromed spool holding arm bracket that is on the right of every thing else[/size][size 3].[/size][size 1]
[/size][black][size 3]3. The two grommets under the angled piece that holds the line stripper are the ones in the documet that are supposed to be used for holding the spool while doing spinning reels. [/size][/black]
[black][size 3]4. The two reddish round parts in the center of the photo, are parts that I do not know what they do, and they are not mentioned anywhere in the directions or the supplimentary supplied trouble shooting information. [/size][/black]
[black][size 3]5. The black odd shaped rubber piece towards the bottom(not included) is one I fashioned to hold the spool bracket steady while spooling.[/size][/black]
[black][size 3][inline 2007_0112Image0012r.JPG][/size][/black]
[signature]