Spinnerbait Problem

[Snags_Alot]

[pirate] I keep loosing my spinnerbaits..they won't stay on my line. I have a swivel hook at the end of my line....the spinnerbait has an open loop on it....Any tricks to stop this from happening?
[signature]

[theangler]

Hello Sangs_alot,
Welcome to bft.

Correct me if I'm wrong but it sounds to me like the open spinner isn't the problem as much as getting snagged and breaking off. I am assuming your knots are holding and if that is the case a good product to try is the Never Snag (or something like that). I have used these and casted straight into huge messes of twigs, weeds , etc ,, and they work. One site that has them is [url "http://www.guardhook.com/"]http://www.guardhook.com/[/url]. There are others out there but these outa do the trick. You can buy different sizes and types and they will work on just about any lure in your arsenal.
[signature]

[DrownedDesertRat]

Sounds to me like the spinnerbait is coming off the snap-swivel. Try tying directly to the line instead of relying on the snap swivel to make things quicker. I always had a really tough time with that. As a novice fisherman I relied heavily on those and now I only use them when fishing with snelled hooks or leaders.

Another trick, if you want to continue to use the snap swivel would be to take a wire twist and wrap it around the bend area of the arm on the spinnerbait and then use some superglue to hold it there. That way there's a lot less room for the snap swivel to move around on the spinnerbait's arm.
[signature]

[Dryrod]

[center][font "Poor Richard"][green][size 4]Is your line being broken or is the swivel coming off the spinner bait? I never seen a spinner lure with an open loop. What brand of lure are you using?[/size][/green][/font][/center]
[signature]

[Snags_Alot]

[] Booyah Spinnerbait,..instead of a loop..there is just a "u" shape to attach your line.....I have no problems with the line or swivel hook.
[signature]

[Snags_Alot]

[] Thanks DDR, and angler......I'll give them a try
[signature]

[Snags_Alot]

[] Well If I had that product in the beginning...I would 've to come up with another Logon...lol.
I have to get me some of those...thanks
[signature]

[aku94]

[reply]
[pirate] I keep loosing my spinnerbaits..they won't stay on my line. I have a swivel hook at the end of my line....the spinnerbait has an open loop on it....Any tricks to stop this from happening? [/reply]

Snags_alot, I believe that your username exploains it all. More likely than not, your spinners are getting snagged on acquatic vegetation, then snapping line. I religously use swivel hooks and that is the only reason why I have lost anything. You should consider trying one of the following things to avoid your prediciment:
1. Use a bobber or float if practical.
2. Reduce the weight of your rig, so you don't sink to as deep a depth.
3. Find a new fishing location, that does not have aquatic vegetation[].

As for the weight reduction, I just recently read an aritcle about that in Outdoor Life . They recomended not exceeding 1/4 to 3/8 ounce where there is known aquatic vegetation. I would use that with caution, because I have run into problems even with those amounts in areas wih vegetation. []
[signature]

[davetclown]

I have tied a few spinner baits,

what it sounds like to me is part of the wire has broken off or you received a peice that had not been caught by inspection, since they are made by machien some times they do get passed that way. no body is perfect nor is a machein.

the other end of the loop should have been tucked in under thread or wire or a bead to close the loop.

I havent seen your lure so I dont know if you can re constitute it by means of shorting it or replacing the stainless steal wire or simply closing the loop with a pair of pliers.

if you throw it on a scaner and cover it with a peice of paper towl we could diagnose the problem correctly and conclusively direct you to the proper solution.....

sory, I just had to use a fifty dollar word before the day was out...[]
[signature]

[davetclown]

here is the demo model I use on my youth fishing programs to demonstrate the construction of a simple spinner bait.

if the problem is with the swivel snap there should be a brass clip to tuck the end of the "U" loop in to or a wire loop to tuck the end of the "U" loop in.

if you are using the latter you may want to swich to a quality brand with the brass catch plate. (I have and continue to use both)

you can avoid the whole problem if you use a swivel barrol insted of a snap. when you use a barrol swivel you tie about a two foot peice of line to tie your lure on to using a polimer knot....

If you need a pic of both rigs let me know and I will scan a couple for you....
[signature]

[DrownedDesertRat]

I believe SnagsA-Lot is using these:



"Using a leader can be a problem when fishing spinnerbaits. Some have no eyelet, just an R-shaped bend in their wire shafts. They slide up a leader's snap-swivel. To alleviate this, wrap a thin strand of wire several times around the R-bend to create an eyelet to hold the snap in place."
(taken from an article by Luigi De Rose, titled "Bass Lures for Pike").
[signature]

[davetclown]

I had one of them a long time ago and just thought it was a manfacturing mistake lol.

I took mine and placed the top part of the R in a vise and raped the blade peice aroud the other one full rotation or two... its been a long time..

Thanks for the clairification....
[signature]

[Dryrod]

[center][blush][font "Poor Richard"][green][size 4]Duh - okay now I understand what he was trying to say. Had a completely different picture set in my mind. Haven't had the problem that was discussed but like the idea posted by DDR.
[/center][/size][/green][/font]
[signature]

[Snags_Alot]

[cool] DDR has exactly the spinnerbait I'm using....Thanks DDR.
I gotta get me a scanner.
[signature]

[Flagmanonice]

I always have mine slide up the spinner , now I just buy the ones with a close end !!

.
[signature]